Ellisys Sense: How Duty Determines the Behavior of RF Energy in the Skin
Duty is one of those parameters that rarely attracts attention at first. Most practitioners initially focus on power, depth, needles, protocols. Over time, however, Duty becomes the setting that defines how predictable, controllable, and repeatable the procedure actually is.
Below is a practical explanation of Duty as it is understood and used in real clinical work.
What Duty means in practical terms?
Duty (duty cycle) describes the ratio between active RF energy delivery and pauses between impulses.
In simple terms, it answers one key question:
Is RF energy delivered continuously, or in controlled pulses that allow the tissue to dissipate heat?
From a tissue perspective, Duty directly affects:
It defines how RF energy behaves inside the skin.
Duty (duty cycle) describes the ratio between active RF energy delivery and pauses between impulses.
In simple terms, it answers one key question:
Is RF energy delivered continuously, or in controlled pulses that allow the tissue to dissipate heat?
From a tissue perspective, Duty directly affects:
- the speed of heat accumulation
- peak temperatures
- uniformity of thermal distribution
It defines how RF energy behaves inside the skin.
Why Duty is essential for stability
RF works through heat.
When heat delivery is poorly controlled, two common outcomes appear:
- excessive thermal load with aggressive skin response
- insufficient heating with limited clinical effect
Duty allows the practitioner to stay between these extremes.
With properly selected Duty:
- tissue warms up progressively
- thermal peaks are reduced
- heat spreads more evenly within the dermis
At this point, Duty becomes a clinical control tool rather than a technical setting.
How Duty influences patient sensation
According to feedback from clinics using Ellisys Sense in routine practice, Duty changes the quality of sensation, not just discomfort level.
With pulsed energy delivery:
- heat feels smoother
- sharp thermal spikes are reduced
- procedures are perceived as calmer and more controlled
Patients rarely describe this in technical language, but they often note that the treatment feels “more even” and “less aggressive”.
How Duty affects tissue response
From a tissue reaction standpoint, several consistent patterns are observed:
1. More uniform erythema
Thermal response tends to be evenly distributed, with fewer localized overload zones.
2. Predictable recovery
Post-procedure reactions become more consistent from session to session.
3. Controlled remodeling
Thermal stimulation remains sufficient to trigger remodeling processes without excessive tissue stress.
What changes for the practitioner
With experience, Duty shifts from a static parameter to a fine-tuning instrument.
Control instead of compensation
Practitioners rely less on:
- reducing power “just in case”
- slowing down excessively to avoid overheating
And more on:
- managing thermal dynamics
- adapting energy delivery to tissue behavior
Adaptation to different zones
The same power level behaves differently with different Duty settings. This allows:
- gentler work in sensitive areas
- maintained efficiency in denser tissue
Reproducibility of results
When Duty is used consciously, outcomes become:
- less dependent on subjective sensation
- more repeatable
- easier to standardize in course treatments
How Duty is typically adopted in practice
In most workflows, Duty usage evolves gradually:
- initially as a secondary setting
- then as a way to smooth skin response
- eventually as the main lever for thermal control
At this stage, Duty stops being a default value and becomes part of procedural logic.
Why Duty gains importance over time
Interest in Duty usually grows after:
- technique confidence is established
- different tissue responses are observed repeatedly
- the practitioner prioritizes consistency over isolated strong results
At this level, Duty supports a calmer, more controlled, and more predictable RF workflow.
In Ellisys Sense, Duty functions as a thermal behavior control parameter.
It influences:
- how RF energy enters the skin
- how heat accumulates and dissipates
- how predictable both tissue response and patient experience become
These are the parameters that tend to remain in long-term clinical use—because they support the practitioner’s control rather than complicate it.
Helping clinics & beauty studios
with marketing and sales
with marketing and sales
Once a week we share our experience and experience of our customers. Subscribe
By clicking the button, you consent to the processing of your personal data and agree to the Privacy Policy.